Technology of laying gypsum tiles with your own hands

Gypsum tiles have to be laid correctly, as not just the aesthetic appearance of decorative facing, but in addition the service

life of the material will be dependent on the technologies of work. The product is more universal, and it can be attached to

concrete, plaster, brick or gypsum board sheets, provided the surface of the base is and has no flaws.

In the event the flaws of the foundation are important, it ought to be completely treated with primer, then a cement mortar is

created, which matches all of the cracks. Then the surface ought to be repeatedly primed and dried. In this case, its makeup

should decide on a particular, comprising elements which block the appearance of fungus and mould.

In the modern interior of the rooms most frequently used gypsum tiles, even imitating natural brick or stone. To execute cosmetic

finishing your self, it is necessary firstly to pick a strategy of tile positioning and prepare a solution. It is important to

focus on the opposite side of the substance. If its surface has an embossed surface, then the glue should be put having an trowel,

also if it is even, then with a top notch one.

The technology of the work is as follows:

* A thin coating of glue is put on the pre-prepared wall. It is spread over the foundation so that it is possible to place 4-5

tiles. Decorative cladding can be placed both on plasterboard, also on putty.

* Cover the rear side of these tiles with adhesive.

* Plaster elements are pressed against the wall and their place is corrected. To align with the seams, it is advised to use


* Finishing is performed in rows, each of which should be changed by half a tile. Facing is completed into the corners of this

space, and then immediately remove any residual mortar at the joints.

Drying the walls takes no more than a day and needs a constant humidity and temperature in the room. The last point in the placing

of gypsum tiles is the decor. To do this, the joints between these components are full of a unique solution, the color of which

suits the brick.

Cosmetic fake of brickwork around the walls is carried out in the following manners:

* Cutting on the darkened surface of the pits of masonry with a bolt cutter along with your own hands;

* placing of tiles under the brick:

* imitating the structure and color of the side surface of a single brick;

* Imitating a fragment of brickwork of many bricks.

The best way to decorate”under the brick” is really the one that permits you to make a usable coating together with the maximum

appearance of its similarity to natural masonry. All three strategies to perform this kind of finishing functions meet the

requirements, however, the cutting of joints using a bolt is more labor-intensive and the creation of large amounts of dust, so

let’s consider more common ways.

The old finish is removed from the walls, and also the surface, if necessary, is leveled to eliminate the requirement to glue

plaster on a thick coating of glue.

Combining such cladding with other kinds of interior finishes can be both systematic and done with no apparent consistency,

chaotically, together with fake of signs of aging.

With the support of decorative gypsum tiles it’s possible to imitate a large number of textures.

A large number of textures can be imitated with the help of cosmetic gypsum tiles.

The wall where it is to be installed must have the following attributes:

* Hardness and strength of the surface;

* The absence of irregular places and sharp gaps;

* no more deformations.

Decorative tiles at the interior of this kitchen

Walls are created from a variety of materials, let’s break down the principles of installation.

When dealing with concrete, there’ll be no big problems. It is simply essential to take into consideration the porosity of the

material. Concrete, that has virtually no pronounced pores, ought to be treated with a good primer.

Mounting gypsum tiles on concrete

Before beginning work on the setup of gypsum tiles on the walls, it is worth assessing the strength of the surface. When the

plaster does not drop off the walls and in exactly the exact same time holds well, you can simply paint it using primer.

Mount the tiles on the painted concrete shouldn’t. The surface should be scratched, making sure to misfire, and it should be

grouted and coated with a coating of plaster.